what size lumber for deck ledger

What is a Ledger Board? | DoItYourself.com

Ledger board is a structural member that is mounted to a vertical frame. Usually, its size is 2" by 10" or 2" by 12" piece of sturdy lumber. Also called a ribbon board or strip, the ledger board is used to attach the deck to the frame of the house.【Get Price】

How to Attach Ledger Board For a Deck | Decks.com

The finished deck height is 1 inch below the bottom of the sill. The decking is 1-inch thick, so the top of the ledger is 1 1/8 inch below the bottom of the sill. In the photo here, the door casing has been cut to the desired top of the deck, so the decking can just slip under the casing.【Get Price】

Laying Out the Deck Ledger Board | Decks.com

Joists are usually installed “on center,” meaning the spacing number – usually, 16" or 12" – falls in the center of the joist’s thickness. Marking for a doubled rim joist at an end of the ledger At the end of the ledger, the outside joist will butt into the face, rather than the end, of the ledger.【Get Price】

Deck Building 4 - Determining Level and Length of Ledger.

The length of the ledger equals the total length of the deck, less 3”. This 3” is so that the joists at either end of the deck will overlap the ledger and be nailed to it. The joists are 1 1/2” thick, hence the 3” reduction in length so that the finished deck will be the designated length. If possible, you will want to have the ledger.【Get Price】

Deck Ledger Board - Best Deck Site

Ledger Board - Deck Attached: When a deck is attached to the house, a ledger board is bolted to the side of the house. To keep water out, metal flashing is carefully installed behind and on top of the ledger board (flashing is not shown). The ledger board itself is 0.40 treated lumber and is chosen for straightness. The rim joist running along the side of the deck laps over the end of the.【Get Price】

Residential Deck Construction Guide - Deck Contractor

1. This document applies to single level residential wood decks only. 2. All lumber shall be identifi ed by the grade mark of, or certifi cate of inspection issued by, an approved lumber grading or inspection bureau or agency (www.alsc. org). All lumber in contact with the ground shall be ap-proved preservative treated wood suitable for ground.【Get Price】

What type of wood is used for ledger boards?

Ledger boards are made from lumber of the same dimensions as the rest of the rim joists on your deck. Depending on the height and size of your deck, the rim joist may be made of 2-by-6 or larger planks. Treated lumber is typically the material of choice, since the deck ledger is exposed to the elements.【Get Price】

Deck Framing: How to Determine Deck Framing Lumber Sizes

According to the Deck Joist and Joist Sizing Chart, 2-by-6 joists on 16-inch centers will span 9 feet 9 inches. With joists just 9 feet 7 1/2 inches long, we add in 1 1/2 inches for the ledger thickness, and another 3 inches for the rim joist which will act as our beam, and the span is exactly 10 feet.【Get Price】

How to attach a ledger to a brick wall

Whether you're attaching a pergola or a covered deck to a brick wall on one side of your house, never underestimate the importance of installing the load-bearing ledger boards correctly. Use a steel measuring tape, carpenter's square and pencil to mark lines on the board indicating the placement of supporting lag bolts; space the bolts 35 to 40 cm (14 to 16 inches) apart.【Get Price】

Ledger size - Forum - Bob Vila

2x6 P.Treated bolted as / the size of your deck. It should be 6-8 inches above grade ideally, but you can get ground contact PT that can be placed closer. You want a flashing that won't react with...【Get Price】

What size should a deck ledger board be?

As a general rule, you should use the same size of board for the ledger as you plan to use for the joists. You can use a larger board, however, if it allows for a better connection to the house framing. Calculate the length as 3 inches less than the width of the deck framing. Click to see full answer【Get Price】

How to Calculate Deck Materials - The Home Depot

Ledger and deck frame size, joist spacing, decking type, railing, railing post size and quantity will be indicated on the drawings as well. Any stairs will be drawn, which will indicate the width and approximate length. With the drawing as a reference, follow the steps below to estimate what and how much you will need to build your deck.【Get Price】

How to Attach Ledger Board For a Deck | Decks.com

The ledger provides much of a deck’s strength; it supports the joists at one end, and it provides stiffness to the framing. (A free-standing deck, of course, does not have a ledger.) The ledger is made of the same material as the rest of the framing—usually pressure-treated lumber.【Get Price】

How to Calculate the Framing Size for a Deck | Home Guides.

How to Calculate the Framing Size for a Deck. A wooden deck is really nothing more than an outdoor floor. It consists of wooden boards laid over a wooden framework consisting of a ledger board.【Get Price】

Installing Deck Ledgers | DIY Deck Plans

A ledger board is a horizontal piece of lumber attached to a wall to support the ends of deck joists. The ledger can be attached using one of three methods. “Through bolts” are driven into brick or stone, then protrude through the ledger, where they are fastened with a nut.【Get Price】

What size is a ledger board? - FindAnyAnswer.com

A 2x8 up to 12 feet; 2x10 to 15 feet and 2x12 to 18 feet. The larger the deck, the larger the joists. In typical deck construction, with a ledger on one side of the joist and beam on the other, the size of the joists is driven by the size of the deck and based on the general maximum spans mentioned above. Click to see full answer【Get Price】

Deck Parts: Joists, Beams, Ledger...

Ledger Board: Whenever the deck is attached to the house, a ledger board is used. In general, ledger boards are the same size as the floor joists. After selecting a straight piece of lumber for the ledger board, the ledger is bolted to the house's framing. Given the potential for injury should the deck break apart from the house, it's important to select the right type of bolt, as well as, the.【Get Price】

Deck Joist Sizing Spacing | Decks.com

A 2x8 up to 12 feet; 2x10 to 15 feet and 2x12 to 18 feet. The larger the deck, the larger the joists. In typical deck construction, with a ledger on one side of the joist and beam on the other, the size of the joists is driven by the size of the deck and based on the general maximum spans mentioned above.【Get Price】

Product Details